What sizes are in a French pattern travertine set?
The short version
A common French pattern set has six pieces in four sizes: one 16 x 24, two 16 x 16, one 8 x 16 and two 8 x 8 inches. It covers 8 sq ft, or about 0.74 m². French pattern and Versailles pattern are the same layout, but sizes vary, so confirm them before ordering.

What is French pattern travertine?
French pattern is a laying pattern that combines several stone sizes in a repeating set, so the surface looks random but the pieces fit together. It is the same thing as Versailles pattern. It is used on patios, pool decks, courtyards and interior floors.
What sizes are in a French pattern set?
The most common set uses four sizes and six pieces.
| Size (inches) | Size (mm) | Pieces per set | Share of area |
|---|---|---|---|
| 16 x 24 | 406 x 610 | 1 | 33% |
| 16 x 16 | 406 x 406 | 2 | 44% |
| 8 x 16 | 203 x 406 | 1 | 11% |
| 8 x 8 | 203 x 203 | 2 | 11% |
Shares are rounded. Some producers use round metric sizes instead, such as 600 x 400, 400 x 400, 400 x 200 and 200 x 200 mm, which changes the coverage per set. If you are extending an existing floor, measure the existing pieces and do not assume a standard.
How much French pattern travertine do you need?
Work out the area, then add your allowance. Order in full sets, because the sizes must stay in the right proportion.
- Measure the net area in square metres or square feet.
- Add an allowance for cuts and breakage. Agree this with your installer, because curves, pool edges and small areas need more than a simple rectangle.
- Divide by the coverage of one set. With the set above, 100 m² needs about 135 sets, or about 810 pieces, before any allowance.
- Order everything together, so the whole area comes from the same production run.
How is a French pattern laid?
The set repeats, but a good layout should not look as if it does. Follow the layout drawing from your supplier or designer, and lay out a section dry before fixing it.
- Avoid long, straight joints running across the area.
- Spread the sizes evenly, so that small pieces do not gather in one place.
- Mix pieces from several crates, so the natural colour variation spreads across the area.
- Keep the joint width consistent, because any error adds up quickly across a repeating pattern.
For the base, bedding and joints underneath, see our guide to installing travertine pavers.
Which thickness and finish should you specify?
Thickness depends on the use. Tiles around 12 mm suit interior floors and walls on a solid base. Pavers around 30 mm are the usual choice outdoors, including pool decks. Follow structural advice for your base and for any vehicle loads.
Tumbled and brushed surfaces are common for French pattern because they soften the stone and suit an outdoor setting. Many sets also have chiselled edges, which give a more rustic look. Our guide to stone finishes compares the options.
What should you check for pool decks and outdoor areas?
Outdoor stone needs more checks than an interior floor, and the answers depend on the stone and the site.
- Slip resistance: wet areas and pool decks need a finish with grip, such as tumbled or brushed. See the finish on a sample, and follow local rules for slip resistance.
- Frost: in cold climates, choose a dense stone suited to freezing conditions, and check that water can drain from the base.
- Filling: decide whether the travertine should be filled or unfilled, and see it on a sample.
- Sealing: agree a sealer and a maintenance plan, especially around salt-water pools.
How should you write a French pattern order?
A clear order avoids the most common problem: pieces that do not match the layout. State these points.
- Stone, colour range and finish
- The exact size of each piece, with tolerances, and the number of pieces per set
- Thickness, and whether the pieces are calibrated
- Edge detail, such as chiselled or straight
- Total area, including your allowance, and the number of sets
- Packing by set or by size, so the site team can mix pieces easily
French pattern sets from our factory
We produce French pattern sets in the sizes you specify at our factory in Denizli, Türkiye, for wholesale and project orders. Tell us the stone, sizes, thickness, finish and total area, and we will quote for your specification. See our French pattern sets for examples of past production.
Frequently asked questions
- Is French pattern the same as Versailles pattern?
- Yes. Both names describe the same multi-size laying pattern.
- How many pieces are in a French pattern set?
- The common set has six pieces in four sizes: one 16 x 24, two 16 x 16, one 8 x 16 and two 8 x 8 inches. It covers 8 sq ft, or about 0.74 m². Confirm the sizes with your supplier.
- Can French pattern travertine be used around a pool?
- Yes, in a paver thickness with a finish that gives grip when wet. Plan drainage in cold climates, and agree a sealing plan.
- Can French pattern be made in other stones?
- Yes. The pattern is a set of sizes, so it can be made in marble or limestone as well as travertine. Check that the stone suits the location.
Sources
- TFO, French pattern travertine layout (set sizes and layout)
- EN 1341, Slabs of natural stone for external paving






